whitep

My postcode is CO10 0NZ so many are asking

Still got it guys...

I have a 3 side dog run with roof. It has about 8.5m length of siding (2 x 2m(one with door) & 3 x 1.5m) good for 3.5 x 1.6m long as a dog run. 1 section of side and 2 of roof are new and unused. Assembled roughly for the photograph. It has all come apart and its roughly 2m square. I transported it on the top of my 6' x 4' trailer. I do have a small shed which is what I used as a kennel, it is 1.5m x .75m. It is not part of this listing but is available to discusson. You can see it at the edge of the photograph. I can deliver locally on my trailer but would need a hand. £300 ono

I have a 3 side dog run with roof. It has about 8.5m length of siding (2 x 2m(one with door) & 3 x 1.5m) good for 3.5 x 1.6m long as a dog run. 1 section of side and 2 of roof are new and unused. Assembled roughly for the photograph. It has all come apart and its roughly 2m square. I transported it on the top of my 6' x 4' trailer. I do have a small shed which is what I used as a kennel, it is 1.5m x .75m. It is not part of this listing but is available to discusson. You can see it at the edge of the photograph. £325 ono

Added

I have a 3 side galvanised dog run with roof. It has about 8.5m length of siding (2 x 2m(one with door) & 3 x 1.5m) good for 3.5 x 1.5m long as a dog run. 2 sections of side and roof are unused. It all comes apart so its roughly 2m square. I transported it on the top of my 6' x 4' trailer. Like I said I have a roof for it and the door has provision for a padlock. I have a .75 x 1.5m shed that I used for a kennel that goes on the end, but I might keep that if the buyer doesnt want it. £350 ono (Over £500 new!)

Sold!

I have a set of Teague Invector Chokes with the 1/2 inch knurled end, not ported. These are in a case with key, sizes Cylinder, Skeet, 1/4, 1/2, 3/4, Full. £150 the set, I have 3/8 and 5/8 too and would consider a bit of a swap for Std Invector chokes as I need to have something to sell with the gun.

Just uplodad them on the advert on Gun Watch guys....

I have a set of original Browning invector chokes with key that came with my Miroku. In good condition, not used in a while since I have a set of teagues which are my shotgun bling! In good condition, in the pic below i know the skeet one looks a little rusty but its just the oil. Sizes are Cyl, Skeet, 3/4, 1/2, 1/4 and full. The key is a decent one that locks in not the crappy friction one. I am looking for £60 paypal gift really.

KW rating is 0.75 so yeah pretty small. But you arent going to run a big lathe on 240v anyway.

Its like a motor controller. You could use it to run an industrial 3 phase compressor or lathe or mill or anything with a 415 volt motor off a normal plug socket.

I have a Danfoss VLT Inverter that is single phase and outputs 3 phases up to 4.2 Amps. Unused but the box is open from me looking and taking pics of it. Pics show the specs. I am looking for SOLD SOLD SOLD

I am selling my Top Gun Waterproof Shooting Jacket. Size is medium. I bought this six months or so ago, but its too small for me. I am a 40" chest and like my fleeces and find it just a little too restrictive. Its fine witha jumper and shirts/t-shirts though. It is a soft suede effect type material and is 100% waterproof. I have only wor it a couple of times and it is in A1 condition. No marks or evidence of it being worn at all. I am a non smoker and it has been kept away from all animals apart from humans. The pockets have poppers at the sides so they can expand and holes in the bottom to drain the water out. Two inside pockets that have velcro to keep whats in them in them! £35 posted, paypal gift preferred but not essential.