Jump to content

Heavy Clay loads Recommendations ?


Gerry78
 Share

Recommended Posts

Wanted to ask clay pigeon shots could they recommend a heavy clay load for shooting DTL I have a new browning A5 Semi auto that i use for ducks when im not using my aya magnum It has 3 1/2 inch chamber and have tried light loads thru it which it doesn't like my mate wants start doing more clay targets off season and will be taking the semi out any recommendations ?

Link to comment
Share on other sites

Cheers lads thanks figgy yes I’ve only took the auto out a few times I put bout 100 of 2 3/4 gamebore steel and 3inch mammoth to loosen it up but when went to clay range tryed GBs it didn’t cycle some of them talking to firearms dealer he said with A5 built like Benellis they can be picky with inertia driven mechanisms but il try them loads yas recommend cheers 👍👍👍👍👍👍

Link to comment
Share on other sites

Gerry, have you stripped your A5 down to it`s individual components and thoroughly degreased it?

Inertia operated guns can be picky with light loads but it doesn`t hurt to get right inside the bolt and ensure that the inertia spring and rotating bolt head is completely unobstructed by packing grease. This modern grease is almost invisible but leaving it on the various moving parts can slow the action down just enough to prevent correct cycling.

Link to comment
Share on other sites

Mudpatten i stripped it down when got it and cleaned it but you could be right there could be grease left behind IM getting fed up with semi autos mate problems with the maxus then sold it now A5 think when i get the queens coins saved trading in for o/u Glad i have my aya s/s As my main gun I Know autos can be picky The mate bought a new beretta A400 Mossy oak xtreme for waterfowl Gas piston same thing spitting out duck cartridges no problems went to clay ground wouldn't cycle light clay loads and thats a gas gun there meant to be more forgiving lol :hmm:

Link to comment
Share on other sites

Gerry I've had a few different autos Beretta among them on my third 3 1/2" gas operated gun for wildfowling, just a hint of fouling on the mag tube and dry rails and you have little chance of cycling clay loads unless they are kicky.

Your A5 will need a good strip and clean with a good degreaser then lubricating on reassembly.

I have little swabs to get in firing pin housing and rails to make sure all the crud is out.

Running your gun with a drop or two in the recoil spring tube in the stock and the slide rails wet as they say with oil makes all the difference in cycling lighter loads, even more so on a new gun. Putting a few hundred heavier carts helps but thousands of them make it slick  on cycling.

Gerry when you get your semi auto run in right they're a great bit of kit. Stick with it.

My Benelli which is well ran in stuck a few times with clay loads short cycling as it was ready for a strip and clean after a thousand or so carts in damp weather, it had bits of powder stuck with other carp that had blown in when using it. 

Over and unders are not without faults.

Edited by figgy
Link to comment
Share on other sites

  • 2 months later...

Good Morning,

I have a couple of autos ( 1gas, 1 inertia) and I run them both on lyvale express power red 27g 7.5.PW. They are a very thumpy cartridge because of the 1500 fps velocity and have cycled all my autos with no problems whatsoever. They can be sourced for reasonable prices on line, but I’m fortunate my local dealer is also very competitive. I have read the pinned topic regarding cartridge velocities as it seems that power red are no where near the claimed 1500 FPS, which has left me wondering why I can definitely feel a difference between them and power gold which are recorded as having a higher FPS but sold with a lower FPS, I’m confused now.

All the best.

Edited by Taileron
Link to comment
Share on other sites

You are very early in your ownership, and i would suggest at least a thousand shots to run it in then strip and relube and you may gave to go with pigeon loads or heavier to get there. Fiocchi do a pl32 in 8 continental size which may be suitable and still use at clay grounds.

 

The A5 was traditionally designed as an ounce and an eighth gun (32g 70mm chambers) and also able to handle 36g comfortably.

In order to make it a 2oz gun (56g 84mm) gun they had to beef up the recoil spring, lengthen the chamber and make the recoil semi auto action longer  to the detriment of lighter loads, patterns and shorter cases respectively.

No matter the advertising blurb, you  have a specialist heavy load/duty wildfowling gun which is not suited to light load clay busting.

If you want a clay gun look for a semi auto that will have 70mm chamber/action and ideally run fine with 21g loads and you can pick up inexpensively such as second hand franchi 712 or similar.

 

Edited by Stonepark
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...