Jump to content
Sign in to follow this  
markyboy07

First attempt at sheath making

Recommended Posts

Ive not been getting as much knife making in as id like recently due to a new job. i have made a few and will get round to writing them up and posting them eventually. I bought some leather tools a while back and have finally got round to using them. I have made one sheath before at a knife making taster day but a lot of the leather work had been pr-prepared so this is the first one from scratch.

i started with a paper template (knifes the wrong way round in the picture i know) and then transferred this to the leather and cut it out.

IMG-20191112-165358.jpg

 

I then wetted the leather and had a go at some stamping, the outside edge pattern was OK but i went a little wrong with the pattern in the centre.

IMG-20191112-174717.jpgIMG-20191112-182236.jpg

i dont have photos for all the steps as i got a bit carried away with what i was doing, but i then shaved some of the leather out of the center and wetted it again to allow it to fold easily. i then used a tool which i dont  know the name of to mark the stitch line, this was quite satisfying to use and for a cheap kit really well made. It has a small sharp hole which cuts a circular cross sectioned sliver out of the leather.

IMG-20191113-170330.jpg 

 

next i cut the welts, which protect the stitching from the blade as well as allow some room for the handle to fit in.

 

IMG-20191113-164616.jpg

IMG-20191114-163011.jpg

These are roughed up with sand paper first before being glued together with contact adhesive.Once the glue had fully dried i used the pricking irons to mark the stitch holes, once they were marked i drilled them through with a hand held drill. i started using a bradel but found that hard work.

IMG-20191114-170251.jpgIMG-20191114-170246.jpg

IMG-20191114-170328.jpg

i shaved the edge of the belt loop to allow it to fit smoothly when glued.

IMG-20191114-162948.jpg

i then started the stitching, i used a saddle stitch which uses two needles, one at each end of the thread and both needles pass each other in the opposite direction going through the same hole.

IMG-20191117-165805.jpg

IMG-20191117-165818.jpg

 

next a bit of leather die and a bit of wet forming around the handle.

IMG-20191118-161503.jpg

IMG-20191118-161523.jpg

IMG-20191201-154908.jpg

IMG-20191201-154952.jpg

 

Once the leather has dried ill use some boot polish and a heat gun to both shine and protect the leather. Its not perfect but a good starting point, i really enjoyed making this and am looking forward to making some more. even though the stamping isn't great you don't really notice it once its been dyed and folded. i'm making a friend a filleting knife so once i've finished the handle i'll be making a sheath for that next, i'll take my time a bit more with that one and hopeful i'll be able to see some improvement.

 

Edited by markyboy07

Share this post


Link to post
Share on other sites

quite right, its been a long day lol now edited

6 minutes ago, Old farrier said:

Good stuff 

well done and for a first time a good result 

thanks for posting and the pictures are very informative 😊👍

Thanks mate, i will also get round to making some tongs at some point honest. 

Share this post


Link to post
Share on other sites
4 minutes ago, markyboy07 said:

quite right, its been a long day lol now edited

Thanks mate, i will also get round to making some tongs at some point honest. 

The weather is against outside jobs stick with the leather work 😊👍

Share this post


Link to post
Share on other sites

If that is your first crackl at it then top marks, very nice.   When I block a sheath...er sorry sheaf :lol:....I make a pattern in wood the same shape as the knife. I then make a set of male and female  pattern blocks which this copy of the knife will fit in. I then wet the leather and trap the two sides of the sheath between with the wood copy acting as the knife. However yoiurs is a fold over sheath whereas mine are stitched all the way around. Just another way of doing it.   Excellent result. 

Share this post


Link to post
Share on other sites

Not bad for only your second attempt, looks very good to me.:good:

Looking forward to the other builds you mentioned.:yes:

Share this post


Link to post
Share on other sites

excellent..very good indeed...wish I was good with my hands....😄😄...atb...misser

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...