Guest rimotu66 Posted November 12, 2013 Report Share Posted November 12, 2013 I want to fit the thin trigger to my 'new' Ultra XS, had a go today and got as far as splitting the action from the stock but it looks like I need to remove a roll pin so I can move the trigger guard out of the way, didn't fancy going that far on a 'new' gun so just wondered if I needed to. Quote Link to comment Share on other sites More sharing options...
shaun4860 Posted November 12, 2013 Report Share Posted November 12, 2013 Surely it's just a case of swapping the blade? If I remember its an Allen bolt and then just slide the old blade off and the new blade on? Quote Link to comment Share on other sites More sharing options...
Gordon R Posted November 12, 2013 Report Share Posted November 12, 2013 You can replace in situ, without dismantling anything. If there doesn't appear to be room, put the safety catch on. I can't remember which position safety has to be in - on or off - but it gives you the room to change triggers. Quote Link to comment Share on other sites More sharing options...
bakerboy Posted November 12, 2013 Report Share Posted November 12, 2013 As per the 2 above, should not take more than a minute or two. Quote Link to comment Share on other sites More sharing options...
MrPhantom Posted November 12, 2013 Report Share Posted November 12, 2013 This post explains it well: http://forums.pigeonwatch.co.uk/forums/topic/57296-changing-trigger-blades-browning-525/ Quote Link to comment Share on other sites More sharing options...
shaun4860 Posted November 12, 2013 Report Share Posted November 12, 2013 This post explains it well: http://forums.pigeonwatch.co.uk/forums/topic/57296-changing-trigger-blades-browning-525/ What a fantastic link..... According to Browning it helps if you move the safety to the rear to prevent firing whilst changing the blade (assuming the gun has the barrels on I suppose) Here is an owners manual for the Citori, thats what most Browning O/U's are called in the states, if you go to page 30 it also describes how to do it, although not nearly as well as TLE http://media.browning.com/pdf/om/08-406citori.pdf Quote Link to comment Share on other sites More sharing options...
Gordon R Posted November 12, 2013 Report Share Posted November 12, 2013 High quality photos and description. Top link. Quote Link to comment Share on other sites More sharing options...
PhilR Posted November 12, 2013 Report Share Posted November 12, 2013 A top tip. When you reassemble the trigger put a touch of Loctite on the thread of the Allen screw. They've been known to come undone twice haven't they Bakerboy! Quote Link to comment Share on other sites More sharing options...
Guest rimotu66 Posted November 13, 2013 Report Share Posted November 13, 2013 Damn, don't I feel daft now, thanks guys and yes a little bit of thread lock will be going on Quote Link to comment Share on other sites More sharing options...
Gordon R Posted November 13, 2013 Report Share Posted November 13, 2013 No need to feel daft. I struggled the first time I changed one. That's how we learn. Quote Link to comment Share on other sites More sharing options...
RAMMER BURT Posted November 13, 2013 Report Share Posted November 13, 2013 have to say that is a top link to do a trigger change very clear info and top pics 10/10 Quote Link to comment Share on other sites More sharing options...
Guest rimotu66 Posted November 14, 2013 Report Share Posted November 14, 2013 Yes it is a top link and mines all sorted now, I had to tickle the thin blade with a needle file as it did not want to slide on but its all good now Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.