Fuji Shooter Posted April 15, 2016 Report Share Posted April 15, 2016 Keep going man you are so far in you have no choice anyway Quote Link to comment Share on other sites More sharing options...
viking Posted April 15, 2016 Author Report Share Posted April 15, 2016 I was expecting to see an LR ascent of Snowden by now........ all good things malk He is suffering from 'cleaners withdrawal' --- must be boring just re-assembling stuff :-) Keep up the good good work im suffering with to much cleaning, not much to go though, oil air cleaner thing, battery holder, prop shafts and i think were done the re-assembly bit will be exciting Keep going man you are so far in you have no choice anyway no choice whatsoever Quote Link to comment Share on other sites More sharing options...
ditchman Posted April 15, 2016 Report Share Posted April 15, 2016 go and get your bolt out and give it a damn good buffing.........you will feel a lot better Quote Link to comment Share on other sites More sharing options...
viking Posted April 15, 2016 Author Report Share Posted April 15, 2016 (edited) mi dont do mi own buffing trust you ditchie to lower the tone Edited April 15, 2016 by viking Quote Link to comment Share on other sites More sharing options...
ditchman Posted April 15, 2016 Report Share Posted April 15, 2016 whilst you are in the doldrums............im going to make a 42mm flogging spanner for the crankshaft damper bolt ...so i will post that up to keep this thread alive .. Quote Link to comment Share on other sites More sharing options...
la bala Posted April 15, 2016 Report Share Posted April 15, 2016 whilst you are in the doldrums............im going to make a 42mm flogging spanner for the crankshaft damper bolt ...so i will post that up to keep this thread alive .. Get on it man Quote Link to comment Share on other sites More sharing options...
malkiserow Posted April 15, 2016 Report Share Posted April 15, 2016 go and get your bolt out and give it a damn good buffing.........you will feel a lot better Your nuts Quote Link to comment Share on other sites More sharing options...
ditchman Posted April 15, 2016 Report Share Posted April 15, 2016 Your nuts not mine someones elses Quote Link to comment Share on other sites More sharing options...
viking Posted April 16, 2016 Author Report Share Posted April 16, 2016 dont think iv mentioned this before when we put engine and gearbox back in but it wasnt sitting straight but ran out of time so just left it, all the brackets on the engine and gearbox are in the right place and its the gearbox end thats not sitting straight, so i can only presume iv got the small brackets that sit on the chassis on the wrong sides as one is at more of a steep angle than the other, thats why iv not had the bulkhead on yet, my mates coming tomorrow so engine should be in straight and bulkhead on couple of hours cleaning today, started on the new/second hand rocker cover seen as painting my other one seriously ******* it up . . Quote Link to comment Share on other sites More sharing options...
ditchman Posted April 16, 2016 Report Share Posted April 16, 2016 well i decieded to make a socket instead of a flogging spanner....found a bit of 5mm plate and squared it off...used a slitting /cutting disc to piece it up Quote Link to comment Share on other sites More sharing options...
viking Posted April 16, 2016 Author Report Share Posted April 16, 2016 then i had ago at the props, or should i say prop Quote Link to comment Share on other sites More sharing options...
ditchman Posted April 16, 2016 Report Share Posted April 16, 2016 squared up the plate then cut it into 6 sides of the socket/box spanner Quote Link to comment Share on other sites More sharing options...
viking Posted April 16, 2016 Author Report Share Posted April 16, 2016 alternator proved to be a bit tricky to clean,and didnt fancy taking it apart, as its not massively seen this will do. Quote Link to comment Share on other sites More sharing options...
ditchman Posted April 16, 2016 Report Share Posted April 16, 2016 (edited) then cleaned the bits up and clamped them to the flats of the damper/crankshaft nut and tacked up Edited April 16, 2016 by ditchman Quote Link to comment Share on other sites More sharing options...
viking Posted April 16, 2016 Author Report Share Posted April 16, 2016 even treated myself to some new dormer drill bits Quote Link to comment Share on other sites More sharing options...
ditchman Posted April 16, 2016 Report Share Posted April 16, 2016 tacked up and ready for full welding... Quote Link to comment Share on other sites More sharing options...
ditchman Posted April 16, 2016 Report Share Posted April 16, 2016 after welding them up and shaping with the grinder and smoothing off Quote Link to comment Share on other sites More sharing options...
viking Posted April 16, 2016 Author Report Share Posted April 16, 2016 oh, and got myself a new dog, but i will start a new thread for that Quote Link to comment Share on other sites More sharing options...
la bala Posted April 16, 2016 Report Share Posted April 16, 2016 Next pictures you post then viking will be bulkhead on Quote Link to comment Share on other sites More sharing options...
viking Posted April 16, 2016 Author Report Share Posted April 16, 2016 after welding them up and shaping with the grinder and smoothing off ditchie, you are a true genius,, who would think of making there own socket set Quote Link to comment Share on other sites More sharing options...
ditchman Posted April 16, 2016 Report Share Posted April 16, 2016 tomorrow i will drill a hole thro' it so a bar can slot thro' it................big sockets are expensive i dont use many so decieded to make the odd one Quote Link to comment Share on other sites More sharing options...
viking Posted April 16, 2016 Author Report Share Posted April 16, 2016 Next pictures you post then viking will be bulkhead on i truly hope so and i hope it will be tomorrow, come rain or shine with or with out my mate, i will get engine straight and bulkhead on Quote Link to comment Share on other sites More sharing options...
la bala Posted April 16, 2016 Report Share Posted April 16, 2016 (edited) Jobs a goodun ditchman, its nice to have stuff around you to make anything you need. Edited April 16, 2016 by la bala Quote Link to comment Share on other sites More sharing options...
ditchman Posted April 16, 2016 Report Share Posted April 16, 2016 nice dog...and nice drill bits........... ...thats the type of dog that sticks close to you....be careful to put it away when you are welding...so it dosnt get arc-eye... Quote Link to comment Share on other sites More sharing options...
viking Posted April 16, 2016 Author Report Share Posted April 16, 2016 nice dog...and nice drill bits........... ...thats the type of dog that sticks close to you....be careful to put it away when you are welding...so it dosnt get arc-eye... got her a mask Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.