krowe79 Posted April 18, 2015 Report Share Posted April 18, 2015 Looking to reload some itx for the 10g the recipe says 12g 5mm gas seal but I can only fine 6.5 or 7 mm does any one no were I can get some please thank you Quote Link to comment Share on other sites More sharing options...
Morningflight Posted April 18, 2015 Report Share Posted April 18, 2015 Why do you need a 12g gas seal for a 10g load ? if its just to pack inside the wad use cork 16g or felt. I have some Ballistic products 12g and 10g gas seals the 12g are 5mm but as I say why 12g ? Eddie Quote Link to comment Share on other sites More sharing options...
krowe79 Posted April 18, 2015 Author Report Share Posted April 18, 2015 its on the recipe from clay and game 12g 5mm gas seal !! New to reloading so wanted to follow to the t all I have read about reloading all say follow the recipe and don't change component Quote Link to comment Share on other sites More sharing options...
krowe79 Posted April 18, 2015 Author Report Share Posted April 18, 2015 Morning flight here is the recipe Hull ren31/2 Primer cx2000 Powder 44.0 csbo Wad bpi tps 10+12ga 5mm gas seal in cup Weight shot 52g itx Rto Cud I use cork ? Quote Link to comment Share on other sites More sharing options...
rbrowning2 Posted April 19, 2015 Report Share Posted April 19, 2015 Assuming you are not sitting on a lot of csb0, you may like to consider a different load, as has been said before on PW csb0 has been discontinued so the load has a limited life now. I am sure others can suggest a replacement load. Quote Link to comment Share on other sites More sharing options...
krowe79 Posted April 19, 2015 Author Report Share Posted April 19, 2015 I have some data from clay and game and I think it's all out off date there's a s lot off component which are not available I will do doe more looking thanks for advice Quote Link to comment Share on other sites More sharing options...
sitsinhedges Posted April 19, 2015 Report Share Posted April 19, 2015 A lot of claygame data is very suspect. More like wish lists than tested recipes Quote Link to comment Share on other sites More sharing options...
krowe79 Posted April 19, 2015 Author Report Share Posted April 19, 2015 I have been in tuch with ballistic products and they have been very good just need a a good suplyer for powder and primers who post out and advice ? Quote Link to comment Share on other sites More sharing options...
10gaugewannabee Posted April 19, 2015 Report Share Posted April 19, 2015 ok so someone has just mentioned the clay and game as a wish list, so the old backside in now very wet when it should not be i used to (!!!!!!!!!!!!!!!!!) up untill 5 seconds ago off clay and game data for the 7 exact types of 12g i reload. i have several books inc the shotgun reloader manual where do i go for clear and presise information that is not going to cause me wet underwear as i collect all the hulls from the local clay range for reloading purposes i need three case recipes as i can have one of three types of cases to use also been looking on a forum someone there has mentioned the cases can be cut long ways in half and sean to confirm the case style and there for the reloading data. where is the information of cross sectional hull pictures or info please Quote Link to comment Share on other sites More sharing options...
sitsinhedges Posted April 19, 2015 Report Share Posted April 19, 2015 ok so someone has just mentioned the clay and game as a wish list, so the old backside in now very wet when it should not be i used to (!!!!!!!!!!!!!!!!!) up untill 5 seconds ago off clay and game data for the 7 exact types of 12g i reload. i have several books inc the shotgun reloader manual where do i go for clear and presise information that is not going to cause me wet underwear as i collect all the hulls from the local clay range for reloading purposes i need three case recipes as i can have one of three types of cases to use also been looking on a forum someone there has mentioned the cases can be cut long ways in half and sean to confirm the case style and there for the reloading data. where is the information of cross sectional hull pictures or info please Ideally you would decide what you want to reload and load a set based around that and send them to the proof house to be sure you are getting performance and safety. You get 4 lots of 5 cartridges tested for £35+vat. Have a couple of grains variation between each lot to get a good idea of what's happening. If you're feeling confident you can just test 4 separate recipes as long as they are all the same gauge. The claygame data is useful but most recipes lack complete data and pressures and some have been shown to be well over proof. I think when it was published they just got any old data floating around and reproduced it as gospel. You will be lucky to find an shells now that are anything other than parallel tube type as seen on the left with a separate base wad and most European data is based on these. Quote Link to comment Share on other sites More sharing options...
10gaugewannabee Posted April 19, 2015 Report Share Posted April 19, 2015 i think i will get the dremal out next week and see what i have about, lol cheers all Quote Link to comment Share on other sites More sharing options...
roughshooter Posted April 19, 2015 Report Share Posted April 19, 2015 I have the data sheets for ITX from C&G but would suggest you look to Ballistic products for advice as I feel you will get a better shell. You do not need massive amounts of ITX but would be better having it at a speed of around 1450 - 1500 fps. This is achievable in the 10g with a 42g load. Go onto Ballistic products website and look at loads of the week archives and check out the "Ripping Fast ITX" Just mho Quote Link to comment Share on other sites More sharing options...
Morningflight Posted April 20, 2015 Report Share Posted April 20, 2015 Krowe79, I think its a miss-print it should be a cork or felt packer inside the shot cup, I dont use that load but I do use CSBO and Multi metal or TPS wads with steel shot and 44 grains, I pack the inside to give a good crimp as long as the shot is just above the wad and set back will push it back into the wad. Not a gas seal especially 12g as this will not go inside a 10g wad. Eddie Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.