BSA-airgunner Posted July 31, 2009 Report Share Posted July 31, 2009 (edited) you will need a front wiper motor 12volt long bolts to space the plates apart and it runs http://www.youtube.com/watch?v=gk4s3_2D2Jo Edited July 31, 2009 by BSA-airgunner Quote Link to comment Share on other sites More sharing options...
shotgun666 Posted July 31, 2009 Report Share Posted July 31, 2009 THESE ARE SPOT ON ,IVE USED ONE FOR YEARS,,MINI OR RELIANT MOTOR I USE,,,,ITS WIERD WHAT WE TRY OUT ISNT IT,,,,,WORKS AND CHEAPER Quote Link to comment Share on other sites More sharing options...
BSA-airgunner Posted July 31, 2009 Author Report Share Posted July 31, 2009 thank you very much.. now i know what to do i recon an afternoon to do one and i have a pillar drill so that makes drilling so easy and as one hole i have done is 20mm...and i enjoy it to boot Quote Link to comment Share on other sites More sharing options...
Wriggler Posted July 31, 2009 Report Share Posted July 31, 2009 What do you use for the arms? I have a couple of lengths of 10 mm bar in the garage or would that be too heavy? Looks good. Quote Link to comment Share on other sites More sharing options...
ryantidgwell Posted July 31, 2009 Report Share Posted July 31, 2009 qaulity looks quite easy to do , just the bit what holds the arms might be the tricky bit but will rustle up something deffinatly going to give this a go top man Quote Link to comment Share on other sites More sharing options...
BSA-airgunner Posted July 31, 2009 Author Report Share Posted July 31, 2009 What do you use for the arms? I have a couple of lengths of 10 mm bar in the garage or would that be too heavy? Looks good. there 6mm fibre glass rods out of my bouncers Quote Link to comment Share on other sites More sharing options...
BSA-airgunner Posted July 31, 2009 Author Report Share Posted July 31, 2009 qaulity looks quite easy to do , just the bit what holds the arms might be the tricky bit but will rustle up something deffinatly going to give this a go top man a piece of u channel pinched to hold the rod tubes and a small weld Quote Link to comment Share on other sites More sharing options...
Wriggler Posted July 31, 2009 Report Share Posted July 31, 2009 Thanks. For the arm holders I just welded some tube at the angle I wanted them. Quote Link to comment Share on other sites More sharing options...
activeviii Posted March 16, 2010 Report Share Posted March 16, 2010 (edited) Sorry wrong post Edited March 16, 2010 by activeviii Quote Link to comment Share on other sites More sharing options...
hodge911 Posted March 16, 2010 Report Share Posted March 16, 2010 nice piece of work but compared to the one i made a tad complicated well done Quote Link to comment Share on other sites More sharing options...
blasterjudd Posted March 16, 2010 Report Share Posted March 16, 2010 Thanks. For the arm holders I just welded some tube at the angle I wanted them. You had best build up your muscles as its gonna weigh something heavy, hope you dont wanna walk far as it will weigh a ton plus dont forget to take a 17ah battery with you as well matey! bet you dont walk far going shootin with this gear??? Quote Link to comment Share on other sites More sharing options...
sitsinhedges Posted March 18, 2010 Report Share Posted March 18, 2010 I have found you can use much lighter plate than is demonstrated here. Think the one I made was only 1.5mm thick and triangular instead of square. The bolts were threaded rod with one end ground to a point to push into the ground Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.