Old farrier

Hi Has there been a decision on the main acomidation venue with food in safe walking distance 😗 And close ish to the ground Being soft and unsure of the area above Watford I wonder if any local could tell me if there is The possobilitys of indoor plumbing hot and cold running water and a ensuite bathroom 😊 Sorry for asking but a touch unsure how far up civilisation reaches 😗 All the best Of

Used linen on the one I built 😊 its generally accepted that its to heavy if you use canvas but I wish your freinds the best of luck are they using it all over the punt or just on the deck ? All the best Of

Hi Sorry to disagree but I think your mistaken I believe traditionally it was linen on the deck and pitch or tar to stop the joints and seal floor canvas strip over the inside joints possibly Although I'm no expert and could well be wrong 😀 It's looking great massive amount of work and effort in it Are you a carpenter by trade if you don't mind me asking All the best Of

My compliments on your skill building that underdog Very nice Op there's som good advice here I won't add as there all more experienced loaders than me Best of luck and enjoy Of

Hi 😂 What is there to say you have got a massive project ahead of you I do take my hat off to you for having a go I hope you get a lot of pleasure and learn a lot from your refurbishment Ii shall watch with interest and admiration All the very best Of

The Toller traditionally named piper we'd bred to look similar to a fox and entice / lure/ drive ducks into a decoy The retriever bit has only recently been added Not suitable for the op in my opinion Lab or golden good companion steady dogs Would do the job All the best Of

Hi will Just to wish you all the best and enjoy 😃 Look forward to hearing about it Have a great time 😃 All the best Of

Hi Well done Lovely rifle and great for you and the gun that you will use it Thanks for sharing All the best Of

Not renouned for there patientce ( leprechauns ) 😗😃😀😂 All the best Of

Hi To be honest if hasn't got hammers its on the slippery slope to the ugly department 😃😀 Bit like a dog with out ears 😃😀 All the best Of

Hi they are aware of the problem at eley and like you found they worked well However I find that amount of case going up the barrel a tad of a worry The fiochie work well as do the Winchester Just to make people aware realy Hope this helps All the best Of

Thanks for the input I agree ther has been a problem As you can see I have experience of one hope they resolve the problem soon All the best Of

Hi No it came off when it was fired its in the 410 trapshooting cartridge thread All the best Of

Not a problem Thanks for your reply All the best Of

Fiochie for me All the best Of

Hi Sorry my link isn't very good and sorry you think I think its law I don't However I do feel as its such a grey area and for my piece of mind it is best policy to submit a gun for re proof after work has been done Hope this clarifies my thoughts All the best Of

These were extra long magnum little rob Rto Didn't have any of the crimp trap ones left and to be honest wasn't to keen on fireing these to get the pictures Not sure if its the same problem with yours but the fiochie seem to work better for my gun and fortunate its a ou so I can easily check up the barrel Hope this helps All the best Of

Hi Well in the spirit of PW I went to the range today to get the empty cases Bottled out after 9 These were rto eley 3inch Anyone want a few empties for Reloding Please anyone using these check up the barrel after each shot I'm sure its just a bad batch but there's issue here in my opinion All the best Of

http://www.gunmakers.org.uk/proofhouse.html Hope this link works It may help some 😀😃 All the best Of

Hi Borrowed this from the net Example of bad work Cut off and re done

Hi appreciate your reply and thoughts and agree with you in a lot of what you say However that only applies if the moderater is on the gun and if its made from a equal strength material Like I said I don't know the law and for peace of mind sent mine for proof The solution is simple over barrel shroud with a screw tightener no need to screw cut All the best Of

Hi Buy both and a mirouke shoot all 3 decide which one you you like then sell all three and upgrade to a higher grade of the one you prefer😗 😃😀😃😃😀 I appreciate this is proberably not the cheapest option 😀😃 Have fun choosing All the best Of Ps iv got all three 😊

That's the weight of the individual coin 😀 Not the weight of the coinage in circulation😀😃😂 So 4x20p and1x50p will give me a 28 gramm load £1.30 cheap non toxic 😗 What fun All the best Of

Think they use a different powder in them between the 2.1/2...and 3 inch shells Could be the cause I have half a box of the 3 inch eley from the bad batch in the interests of science and being stupid I will fire them on Sunday and. If I survive I post the pictures All the best Of

Hi Jo Don't know how many failed but I do know how many I messed up learning how to screw cut them I was practicing on scrap barrels It is a precision job and a lot of materiel to remove from some of the heavy bull barrels and very important to leave the correct amount to put the thread into Best advice pay a proffesional gunsmith and go for re proof Just my thoughts All the best Of