powler Posted November 16, 2015 Report Share Posted November 16, 2015 Guys any recommendations for a moderator cover, the moderator is a Ase Ultra Jet z Compact, measurements 18cm long x 4cm diameter. The Jack Pyke ones look like they are to big at 5cm diameter, and dont really want to wrap tape around it as this could hold moisture. Just looking to protect it from knocks etc. Thanks Mick Quote Link to comment Share on other sites More sharing options...
steve_b_wales Posted November 16, 2015 Report Share Posted November 16, 2015 I use the self cling camo' bandage. If it get wet or damp, I just unwrap it and dry it out. It does not leave any marks on the moderator. Quote Link to comment Share on other sites More sharing options...
Bluebarrels Posted November 16, 2015 Report Share Posted November 16, 2015 I use the self cling camo' bandage. If it get wet or damp, I just unwrap it and dry it out. It does not leave any marks on the moderator. I use the same stuff on my Hushpower good stuff BB Quote Link to comment Share on other sites More sharing options...
Velocette Posted November 16, 2015 Report Share Posted November 16, 2015 A piece of bicycle inner tube is all you need. There are all sizes from very thin "roadie" type to extra wide downhill MTB ones. Quote Link to comment Share on other sites More sharing options...
Remimax Posted November 16, 2015 Report Share Posted November 16, 2015 (edited) Guys any recommendations for a moderator cover, the moderator is a Ase Ultra Jet z Compact, measurements 18cm long x 4cm diameter. The Jack Pyke ones look like they are to big at 5cm diameter, and dont really want to wrap tape around it as this could hold moisture. Just looking to protect it from knocks etc. Thanks Mick Guys any recommendations for a moderator cover, the moderator is a Ase Ultra Jet z Compact, measurements 18cm long x 4cm diameter. The Jack Pyke ones look like they are to big at 5cm diameter, and dont really want to wrap tape around it as this could hold moisture. Just looking to protect it from knocks etc. Thanks Mick make yer own,get a small square of neoprene off fleabay roll it round mod to get sze then cut 5mm shorter for snug fit. 2 coats of evostik contact adhesive along 2 edges let it touch dry then push edges together for tidy seam. cut a disc with hole for top and glue the same. take you about 30mins to make and cheap as chips. i use 5mm thick neoprene but 3mm would do.. got a sonic 45 and could not find one to fit so knocked one up. Edited November 16, 2015 by Remimax Quote Link to comment Share on other sites More sharing options...
nighteye Posted November 16, 2015 Report Share Posted November 16, 2015 That's great advice , I have a sonic 45 , cheers 😀 Quote Link to comment Share on other sites More sharing options...
Bewsher500 Posted November 16, 2015 Report Share Posted November 16, 2015 inner tube on both of mine water tight, matt finish, silent and reduce the "ting" Quote Link to comment Share on other sites More sharing options...
Dougy Posted November 16, 2015 Report Share Posted November 16, 2015 I have a neoprene mod cover for my AseS5 it's doing a wonderful job keeping my gear knob warm. I see them as just something to make the mod bigger. Quote Link to comment Share on other sites More sharing options...
powler Posted November 17, 2015 Author Report Share Posted November 17, 2015 Thanks for the ideas guys, will have a go at knocking one up. If it works ok I will stick a photo up . Thanks Mick Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.