Jump to content

fixing my safe to the wall


Sco77w
 Share

Recommended Posts

  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

when she came round she said "is it bolted to the wall" i replied that it was and opend the safe to point out the bolts

 

that is when she grabbed the door and with her whole body she was properly yanking at it....i did tell her to stop becouse i thort she was going to have it off the wall...

 

it took me a week to get over what she did i was boiling inside and if she had managed to get it off the wall and seized my firearms???

 

 

could she do that??

 

In the real world it wouldnt be possible for a thief to swing off the door because they need to get it open in the first place and therefore have no need to remove cabinet from wall.When the door is locked shut theres nowhere on a cabinet you could effectley use as leverage so was a bit silly for her to use so much effort unless she was demonstating her athletic prowness and was comming onto you.

Link to comment
Share on other sites

It's the "presumption" you will get a licence that they don't like.. Well in our area it is...

I ordered the cabinet for my air rifles before I put my application in.

I have 2 daughters under 18, and although they have used my air rifles and have been taught to respect and not touch them without permission, I wanted to make absolutely sure in the future that they or their friends could not get hold of them.

 

I am being anything but presumptuous in my application, if I don't get my SGC the cabinet stays where it is and just houses my air rifles.

Link to comment
Share on other sites

I ordered the cabinet for my air rifles before I put my application in.

I have 2 daughters under 18, and although they have used my air rifles and have been taught to respect and not touch them without permission, I wanted to make absolutely sure in the future that they or their friends could not get hold of them.

 

I am being anything but presumptuous in my application, if I don't get my SGC the cabinet stays where it is and just houses my air rifles.

I had my safe a year before i got round Applying for my SGC. As above i used it for my Airguns and still do. FEO was more concerned where the cabinet was ie. out of sight from anybody (not in view of a window)and he definately never swung off the door.

Link to comment
Share on other sites

That's all I did.

 

Bolt it down as best you can, my house is old and no straight walls.

 

Had about 4mm gap at the top half of the cabinet.....filled the void with three tubs of "no more nails", ran some down the sides as well, cleaned it up and Roberts your fathers brother.

 

No problems at all when checked.

 

 

 

 

thats exactly what i did,only, the feo told me to do it,then after i had done it i had to email him to say it had been done,no problems...

 

DAZ

Link to comment
Share on other sites

Theres no space in my bedroom for a gun cabinet as i have too many power tools stored under my bed. :lol:

 

and yes before anyone points it out, I can only get away with that because its my house and i'm single! :D

just read this and still laughing i have too many power tools under my bed and I'm single o dear if it keeps you happy high powered dreams :lol::wub::blush:

Link to comment
Share on other sites

I had this issue recently when I moved into my new house, new build with standard irritating plasterboard rubbish. Originally went into the concrete floor but the FEO's piece of paper says the wall, which is weaker, but hey ho.

 

He also wanted flush to the wall, not with a piece of board so that meant a plinth for the cabinet to sit on. Took me a weekend to get teh bloody thing mounted but got there in the end. Trick to the gap was easy in the end - measure the gap between the back of the plasterboard and the blockwork (easy enough so long as you have a nice long bolt) and then put the 4 bolts through the cabinet ahead of mounting to the wall.

 

Add nuts on the back of them to the right spacing plus washers on either side of the cabinet, and when you screw it all up, tight as anything and works a charm. You are effectively ignoring the plasterboard all together.

Link to comment
Share on other sites

i had the same problem with my walls being a new house its dry lined with dot and dab and all i did was drill throught the plaster board and in to the block used threaded bar and secured it in with chemical fixing resein(screwfix) and it set as hard as rock and when my fao came he was more than happy with the way it was done so no need to remove any plaster board when you tighten it up to wall dont over do it as they may be risk of pulling it through the plaster board

Link to comment
Share on other sites

are they allowed in the loft?

 

My mate had his fitted in the loft, FEO said if the loft floor was not boarded out to the cabinet she would not be allowed to go up and inspect it, also if the loft did not have easy access (built in loft ladder) they could refuse on the basis that its too awkward for him so he might be tempted to not use the cabinet as soon as he returned home from a shoot so have & his tea / shower first etc..

 

But his was approved.

Link to comment
Share on other sites

  • 3 weeks later...

Well.....An update on this saga,

 

Just had a call from the feo,

and its not good, have been told the drywall lining HAS to be cut out to allow the cabinet to go back against the blockwork.

 

Wouldn't listen to any form of reasonable argument against this so being in a privately rented house looks like I'm jiggered unless I can get the thing up in the loft (sheeeesh it's heavy)

 

Gotta get it in place for next Wednesday AM :unsure:

Link to comment
Share on other sites

and its not good, have been told the drywall lining HAS to be cut out to allow the cabinet to go back against the blockwork.

 

That's c**p.....

 

I guess you got your FEO on a bad day...... I had no such problem at all with this and even have it bolted 3 inches off the ground and nothing was said about the gap underneath.

 

This is where there should be a uniform agreement countrywide. What is the point of one area saying it isn't a problem, then another saying it is..... :hmm:

Link to comment
Share on other sites

That's c**p.....

 

I guess you got your FEO on a bad day...... I had no such problem at all with this and even have it bolted 3 inches off the ground and nothing was said about the gap underneath.

 

This is where there should be a uniform agreement countrywide. What is the point of one area saying it isn't a problem, then another saying it is..... :hmm:

C**P Indeed !! and totally rollocks :angry:

 

His reasoning being was that with the cabinet against drywall board its to easy to jam a prybar/jemmy into(through) the plaster board and lever the cabinet off the wall and rip the bolts out of the brickwork.

 

:angry: Bloody hell you'd need a tow truck so long as I put all six bolts into the blockwork properly, and the cupboard is only around 2ft square so not alot of room for leverage.

 

Apparently, according to him, this cutting out drywall is the new std requirement in Essex for new applications.

Edited by TaxiDriver
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.

×
×
  • Create New...