Dave-G

And yet it seems .gov are about to commence another contract with Fujitsu.

I've just noticed on the top left in the photo of the welder how really modern it is - seems to be a fully woke one... its all inclusive... Lesbian Gay Bi Trans.

I'm starting to get into this a bit now - this new type of arc welder is far superior to my old transformer type that wouldn't get down to low enough amps to attempt any chassis welding. At this low 30 amps current and using its HOT START feature I found I had to 'warm' the 1.6mm rods off the target area before it would 'soft-arc' where I wanted it if that makes any sense. I welded some 1mm plate over the hole to make it level with an original overlap then welded a slimmer piec to join them up and fill any gaps. This was into the longitudinal box section inside the front wheel arch of a 2001 reg Shogun Pinin project car. I only had a couple of blowthroughs by using a quick touch on and off method to more or less spot weld around the plate. I let the Kurust I liberally applied to dribble through and behind any gaps to dry before applying underseal to seal the job.

Ah... but were you asking for advice and not returning to read any replies?

I have exactly the same issue with W7, I use Chrome browser if that matters.

Wonder if it's been skipped over because Palestinians seem to be allowed to do what they want over here as most orgs are afraid of upsetting them.

If squirrel is going to be a high percentage of your outings - and fox mostly rare I suggest the lower mag will suffice and help spot close up tree use without being too zoomed in. Foxes are so much larger and though they'd be small in the viewer all you need is to know if one is there and wait for it or close the distance, so a fox 'finder' albeit bereft of detail is fine with your budget in my opinion.

Strewth - some very lucky people there - and seemingly some unlucky people in the other aircraft.

Agreed.

seems odd that crazy Khan wants cleaner air in London then allows so much pollution to spoil the air quality - let alone the cost.

Yep - most feature heavy inclusivity these days, the most grating to me are fatty nothing like feminine wimen. Even Emmerdale has been infected with serious gaiety.

I see the OP hasn't been back to check replies to his question.

I think she's quite hot but the wife can't stand her.

Mine is that horrible nasal Alan Carr, particularly in the advert for ITVX. I can't imagine anyone less likely to want to use anything 'it' promotes. I say it because its neither a male nor female in my opinion and I think it makes UK males look effeminate nasal whiners. I'll leave it there so I don't get banned because we can't say what we think sometimes.

Compare sites need to have people reading all of the prompts. They like to sneak in tricks like seriously undervaluing a car under cover of a "this is what we think your car is worth window" too... be careful.

And when it gets to the valuation stage, they only pay what it cost you: so if a piece of wood was 10 pence and you spent ten hours shaping it the compensation is 10 pence.

Mine pops out sometimes when climbing under the car for example it goes back in when I straighten up, very painful, my sympathies.

I've just bumped my .22 FAC BTAS FX CYCLONE carbine for sale. It has a lever at the left side of the action that has three power settings, the lower is about 16 FTlb, middle about 18 and top power selection just over 26FTlb. It is seriously lightweight and has a shot count of forty while still on the regulator before dropping down, Anyone needing more shots than that on an outing is dreaming of a white Xmas reoccurring. I'm visiting family Dec 24/25/26 and don't do online wi my - mobile so be patient if you want a reply - or respond today up to midnight. You have not disclosed your whereabouts.

Xmas bump.

Thassa cracker.

6-12 max mag is more than enough for HMR. Remember higher mag is more focus fussy and reduces light passage... important if you might use an add on night vision with it.

I got a bit brave and tried making good a wheel arch - welding a strip of 1.5mm steel mostly to a rear inner wing fold over using 1.6 negative electrode, earthed direct to the new steel. It holds but I've not put much weight on it I blew through a couple of places. Next stage is to weld some 1mm plate to that new metal and the inner wing to make a base for some P38. I sparked up on the new steel then quickly strayed to the old metal.

Ah so stop criminal gangs having access to transport - yea that should do it.

We can only hope some Palestinians eventually realise that turning over or shopping Hamas fighters and weapons will get their pain done with sooner.