nagantino Posted August 22, 2022 Report Share Posted August 22, 2022 I reload lots of .38 Sp, .357 and .44 magnum with small gallery powder loads. Being able to see the powder down inside the case is important, and I’ve noticed new brass makes it easy. Old brass not so easy because of the sooty deposits. Would an ultrasonic cleaner remove the deposits inside the case? I load on a Lee Pro 1000 and I can get lovely shiny brass on the outside of the case with all the usual methods. Has anyone used an ultrasonic cleaner to do this? Don’t like the steel pins idea as it sounds like too much trouble but I'm interested in ultrasonic method. Anyone use that method? Quote Link to comment Share on other sites More sharing options...
Newbie to this Posted August 22, 2022 Report Share Posted August 22, 2022 (edited) I occasionally use an ultrasonic cleaner on my .38 special brass in conjunction with the tumbler. So I tumble them first, then deprime, then I will occasionally if I think it is needed, clean them in the ultrasonic,rinse well and dry them in a food dehydrator, then give them another tumble as they tend to go dull after the ultrasonic clean. It will get all the soot off inside and in the primer pocket (if deprimed), I usually put them on a 30 minute cycle at 60°, with a home made cleaning solution. Edited August 22, 2022 by Newbie to this Quote Link to comment Share on other sites More sharing options...
oowee Posted August 22, 2022 Report Share Posted August 22, 2022 Its all I use. Quote Link to comment Share on other sites More sharing options...
steve_b_wales Posted August 22, 2022 Report Share Posted August 22, 2022 (edited) I use an Ultrasonic cleaner with Birchwood Casey brass cleaner. The liquid cleaner is excellent on it's own, but used with the sonic cleaner, it's excellent. Birchwood Casey brass cleaner makes 2 gallons. Edited August 22, 2022 by steve_b_wales Quote Link to comment Share on other sites More sharing options...
ditchman Posted August 22, 2022 Report Share Posted August 22, 2022 anyone tried clock cleaning fluid.........makes a spanking job....would need to tumble them in medium afterwrds tho Quote Link to comment Share on other sites More sharing options...
oowee Posted August 22, 2022 Report Share Posted August 22, 2022 1 hour ago, ditchman said: anyone tried clock cleaning fluid.........makes a spanking job....would need to tumble them in medium afterwrds tho What is it? Quote Link to comment Share on other sites More sharing options...
ditchman Posted August 22, 2022 Report Share Posted August 22, 2022 (edited) 30 minutes ago, oowee said: What is it? aint got a clue.....have seen before and after of clock mech's....impessive................it stinks tho https://www.amazon.co.uk/Ultrasonic-cleaning-solution-concentrate-sensitive/dp/B00L0EJ498/ref=asc_df_B00L0EJ498/?tag=googshopuk-21&linkCode=df0&hvadid=344352605429&hvpos=&hvnetw=g&hvrand=16998977740169732229&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9041117&hvtargid=pla-698684181522&psc=1 30 minutes ago, oowee said: What is it? Edited August 22, 2022 by ditchman Quote Link to comment Share on other sites More sharing options...
oowee Posted August 22, 2022 Report Share Posted August 22, 2022 2 hours ago, ditchman said: aint got a clue.....have seen before and after of clock mech's....impessive................it stinks tho https://www.amazon.co.uk/Ultrasonic-cleaning-solution-concentrate-sensitive/dp/B00L0EJ498/ref=asc_df_B00L0EJ498/?tag=googshopuk-21&linkCode=df0&hvadid=344352605429&hvpos=&hvnetw=g&hvrand=16998977740169732229&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9041117&hvtargid=pla-698684181522&psc=1 Looks an interesting product. https://www.carbusonic.co.uk/ Quote Link to comment Share on other sites More sharing options...
ditchman Posted August 22, 2022 Report Share Posted August 22, 2022 23 minutes ago, oowee said: Looks an interesting product. https://www.carbusonic.co.uk/ i use mr muscle oven cleaner...then power waash off...let it dry and spray with WD40..cept i dont spray the moving pats like throttle links...as they get sticky and gummed up Quote Link to comment Share on other sites More sharing options...
Imperfection Posted August 22, 2022 Report Share Posted August 22, 2022 I use an ultrasonic cleaner. I bought it years ago from Aldi after someone on here posted that they had them for sale for £20. Best additive i've tried is jif...the stuff you put on your pancakes. I buy the cheapest lemon juice i can get, add to warm water in the unit and leave going for little while. The primer pockets in particular are always clean. Quote Link to comment Share on other sites More sharing options...
Savhmr Posted August 23, 2022 Report Share Posted August 23, 2022 I use one with SeaClean solution my compact U/C cleaner....2 caps per 400l warm water. Does a cracking job and unlike the "clock cleaner" mentioned above does not contain ammonia. Best to avoid any cleaner with ammonia as it can damage your brass. 23 hours ago, Imperfection said: I use an ultrasonic cleaner. I bought it years ago from Aldi after someone on here posted that they had them for sale for £20. Best additive i've tried is jif...the stuff you put on your pancakes. I buy the cheapest lemon juice i can get, add to warm water in the unit and leave going for little while. The primer pockets in particular are always clean. Jif's highly acidic but cleans well. You can also just squeeze the juice from half a lemon into warm water for the same effect! Quote Link to comment Share on other sites More sharing options...
Imperfection Posted August 23, 2022 Report Share Posted August 23, 2022 34 minutes ago, Savhmr said: Jif's highly acidic but cleans well. You can also just squeeze the juice from half a lemon into warm water for the same effect! Never had any issues with lemon juice and some of my brass has been reloaded/cleaned multiple times. I've even tried using powdered citric acid but was cheaper to buy Aldi/Lidl lemon juice which does same job. Quote Link to comment Share on other sites More sharing options...
steve_b_wales Posted August 23, 2022 Report Share Posted August 23, 2022 As mentioned previously, I use Birchwood Casey brass cleaner, which alone, cleans cases pretty good, especially if the fluid is heated first. One bottle makes 2 gallons of cleaner. Quote Link to comment Share on other sites More sharing options...
Blackjack Posted September 1, 2022 Report Share Posted September 1, 2022 I use an ultrasonic cleaner. Recipe as follows: 1.5 litres of hot (60 centigrade water) - the heat helps to break stuff down. 1 teaspoonful of citric acid crystals (or 100 ml of white vinegar) - dissolves most gunk. 1 tablespoon of washing up liquid - binds the dirt to the water and degreases cases. After 20 minutes of ultrasonic cleaning, rinse in tap water in a bowl and then add 1/2 teaspoon of bicarbonate of soda to neutralise any remaining acid traces. Leave to stand for ten minutes with the bicarbonate solution then rinse again with tap water and drain off as much water as possible. Tip onto clean dry tea towel and dry as best you can. Don't touch with your hands. Then place on clean, flat oven tray and pop in oven at about 80 centigrade until dry. Leave to cool naturally and then enjoy your shiny brass! Mmmmmm........tasty! Quote Link to comment Share on other sites More sharing options...
steve_b_wales Posted September 2, 2022 Report Share Posted September 2, 2022 A very quick and easy way to dry cases is to put them in an air fryer. I add 20-30 to the basket and set the fryer on medium for approx' 3 minutes. The cases come out bone dry without an damage or discolouration. Quote Link to comment Share on other sites More sharing options...
Kev1gun Posted September 2, 2022 Report Share Posted September 2, 2022 Wet tumble with stainless steel pins is what I use, ive tried all the other methods but Wet tumble with stainless steel pins and 1 teaspoonful of fairy liquid and a tablespoon full of rinse aid, 2 hour tumble then thy come out brand new. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.