Jump to content

Loose rib advice


wg2
 Share

Recommended Posts

Hi All,

I would really appreciate some advice on a loose rib I've just noticed. It's on a George bate sbs. I don't know if it's worth getting repaired or not. I paid £300 for the gun, I really like it and don't want to scrap it, however as I understand it a loose rib is around £400 to repair as it has to be re-blued aswell. Could I just carry on using as it is? How long is the gun likely to last as I think it starts corroding under the rib if left?

 

Any advice is much appreciated

 

Wg

Link to comment
Share on other sites

It is impossible to say how long the barels will last with a loose rib, because you cannot see below the rib to see what rusting/corrosion is currently taking place. If you use it on a wet day a certain amount of water will get under the rib which you wont be able to dry out. This will result in rust forming; which in the end will result in rust pitting that reduces the strength of the barrel wall.

 

The fact that it is an old English gun points to the ribs being soft soldered. This allows them to be removed by a competent gunsmith. Any corrosion can be then be removed and the ribs cleaned and relaid. The process is all hand work, and the job of cleaning up after re-soldering will result in the blacking / blueing being removed in places. So the barrels will need re-blacking after the work of relaying the ribs is complete.

 

The only way you are going to get an accurate quote as to cost is to take it to a decent gunsmith and seek his advice on what needs doing and the price.

 

Only you can decide whether the gun is worth the money. You havent said whether its an ejector or non-ejector, however; you are not going to get a half decent replacement for what it will cost you to get it fixed.

 

The website for my local gunsmiths (East Grinstead Guns - Sorrel Brothers) are quoting £368 + VAT for relaying the ribs and re-blacking. So your advice of around £400, doesnt seem to be to wildly out

Edited by JJsDad
Link to comment
Share on other sites

I relayed around 80 ribs last year and £35 plus VAT is about right . Doesn't matter what the gun is its the same amount of work .

Down to you to decide . As to whether you can shoot it or not will depend on how loose they are now , they will get worse . By the way I really hate it if some one has decided to use super glue as a temporary repair as it stinks the shop out for ages .

Link to comment
Share on other sites

I relayed around 80 ribs last year and £35 plus VAT is about right . Doesn't matter what the gun is its the same amount of work .

Down to you to decide . As to whether you can shoot it or not will depend on how loose they are now , they will get worse . By the way I really hate it if some one has decided to use super glue as a temporary repair as it stinks the shop out for ages .

do you mean £350
Link to comment
Share on other sites

Hi All,

I would really appreciate some advice on a loose rib I've just noticed. It's on a George bate sbs. I don't know if it's worth getting repaired or not. I paid £300 for the gun, I really like it and don't want to scrap it, however as I understand it a loose rib is around £400 to repair as it has to be re-blued aswell. Could I just carry on using as it is? How long is the gun likely to last as I think it starts corroding under the rib if left?

 

Any advice is much appreciated

 

Wg

 

£400 seems steep!

 

I relayed around 80 ribs last year and £35 plus VAT is about right . Doesn't matter what the gun is its the same amount of work .

Down to you to decide . As to whether you can shoot it or not will depend on how loose they are now , they will get worse . By the way I really hate it if some one has decided to use super glue as a temporary repair as it stinks the shop out for ages .

 

I would suggets you send this man a PM!

Edited by HDAV
Link to comment
Share on other sites

It is viable to do yourself if you understand soldering. I did one myself a couple of months or so back...just need to get around to getting it reblacked. Follow the basic soldering principle of clean the metal to a shine, thoroughly degrease and then resolder. Take your time with heating it up but if you know what it looks like when solder runs, you'll be ok.

Edited by -Mongrel-
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...