Minky Posted July 10 Report Share Posted July 10 6 hours ago, snarepeg said: From Chambers £24 posted, but made one up on the lathe from 6 mm stainless steel 👍🇬🇧 Good man. At £24 for a replacement pin it would have been cheaper to buy one or even two guns at auction and dismantle/ scrap for pins, springs, screws, extractors, beads. Ejector springs... in fact everything that isn't a pressure bearing part.... so how sticky was the firing pin.? Quote Link to comment Share on other sites More sharing options...
snarepeg Posted July 10 Author Report Share Posted July 10 2 hours ago, Minky said: Good man. At £24 for a replacement pin it would have been cheaper to buy one or even two guns at auction and dismantle/ scrap for pins, springs, screws, extractors, beads. Ejector springs... in fact everything that isn't a pressure bearing part.... so how sticky was the firing pin.? It had shortened thru use. So measured and made one to same dimensions but a mm longer.👍🇬🇧 Quote Link to comment Share on other sites More sharing options...
Andy H Posted July 10 Report Share Posted July 10 (edited) As you have access to a lathe make one out a shank of an 11/12/13mm drill and harden and temper that is the steel to use, I have an old sxs zabala I have had for just under 40 years but in the first 2 years both pins snapped , Made new one's out of old drill shanks' and no problem's since. Edited July 10 by Andy H Quote Link to comment Share on other sites More sharing options...
old'un Posted July 11 Report Share Posted July 11 9 hours ago, Andy H said: As you have access to a lathe make one out a shank of an 11/12/13mm drill and harden and temper that is the steel to use, I have an old sxs zabala I have had for just under 40 years but in the first 2 years both pins snapped , Made new one's out of old drill shanks' and no problem's since. 11/12/13mm drill???….what diameter are your firing pins? I presume you are using carbon steel drills? Quote Link to comment Share on other sites More sharing options...
snarepeg Posted July 11 Author Report Share Posted July 11 1 hour ago, old'un said: 11/12/13mm drill???….what diameter are your firing pins? I presume you are using carbon steel drills? The firing pins are 13mm long, striker end is 2.5mm diameter shoulder 6mm and hammer end 4mm. did make one out of 6 mm drill, its firing fine, quite chuffed for making bits and bobs that work, bin the bits that havnt, every day a school day👍🇬🇧😊 Quote Link to comment Share on other sites More sharing options...
TIGHTCHOKE Posted July 11 Report Share Posted July 11 I always used to use No 6 drifts, cut down but left over length. Then fitted and "fired" on an already fired cartridge to prove it was overlong. Then removed and dressed to the correct length, never had one need doing twice. Quote Link to comment Share on other sites More sharing options...
Minky Posted July 11 Report Share Posted July 11 (edited) I'm so glad that there are still some of us out there who have the equipment, the knowledge and ability to do stuff like this. All I get told is... GET RID OF THIS JUNK !!! To which I reply.. IT"S ONLY JUNK UNTIL YOU NEED IT OR YOU WANT ME TO MAKE OR MEND SOMETHING FOR YOU.!!! To which I would also add... I've still got XYZ £ in my pocket... You've got jack in your pockets. I know that there are limits to what you can horde but it always seems to be a case off .. a week or two after something has been thrown out that you need a bit of it and then have to go out and but what you just threw out. Ps. it's nice to know the dimensions of the pins for future reference. I did have a Mainspring break on my No. 4. right in the middle of a day. Undaunted I carried on using the left barrel. Edited July 11 by Minky Quote Link to comment Share on other sites More sharing options...
old'un Posted July 11 Report Share Posted July 11 5 hours ago, snarepeg said: The firing pins are 13mm long, striker end is 2.5mm diameter shoulder 6mm and hammer end 4mm. did make one out of 6 mm drill, its firing fine, quite chuffed for making bits and bobs that work, bin the bits that havnt, every day a school day👍🇬🇧😊 Yep, it was more a question why Andy H was using 11/12/13mm drill bits when the maximum diameter of most pins are around 6mm. Best steel for firing pins is silver steel, are yours spring return? Quote Link to comment Share on other sites More sharing options...
snarepeg Posted July 11 Author Report Share Posted July 11 59 minutes ago, old'un said: Yep, it was more a question why Andy H was using 11/12/13mm drill bits when the maximum diameter of most pins are around 6mm. Best steel for firing pins is silver steel, are yours spring return? Yes, very small coil in front section to push back ss hammer recocks. Quote Link to comment Share on other sites More sharing options...
Andy H Posted July 11 Report Share Posted July 11 (edited) 3 hours ago, old'un said: Yep, it was more a question why Andy H was using 11/12/13mm drill bits when the maximum diameter of most pins are around 6mm. Best steel for firing pins is silver steel, are yours spring return? When the machine you are using weigh's 2 1/2 tons and the chuck is 400 odd mm across and will not hold 6mm stock due to jaw's being ground true over the year's. Edited July 11 by Andy H Quote Link to comment Share on other sites More sharing options...
ditchman Posted July 11 Report Share Posted July 11 3 hours ago, snarepeg said: Yes, very small coil in front section to push back ss hammer recocks. i used a cut down biro spring on my hammer gun.. Quote Link to comment Share on other sites More sharing options...
snarepeg Posted July 12 Author Report Share Posted July 12 9 hours ago, ditchman said: i used a cut down biro spring on my hammer gun.. Yes, got some of those 👍 Quote Link to comment Share on other sites More sharing options...
old'un Posted July 12 Report Share Posted July 12 12 hours ago, Andy H said: When the machine you are using weigh's 2 1/2 tons and the chuck is 400 odd mm across and will not hold 6mm stock due to jaw's being ground true over the year's. Sorry, I thought you were suggesting snarepeg make them out of that size drill. “As you have access to a lathe make one out a shank of an 11/12/13mm drill” Quote Link to comment Share on other sites More sharing options...
snarepeg Posted September 25 Author Report Share Posted September 25 Finally a result gents. with stock and bottom plate removed on cocking quite a gap between hammer bent and sear, when closing action this equates to a loss of hammer throw so less energy. got a 12 bore hammer spring and sear from Southertons for 14/95 pounds posted. Ground sear and spring down to slot in action, sear was longer so dremmeled down to fit at full opening of action. this gives a longer throw of the hammer. cocks nice and fires so perseverance finally won.👍🇬🇧 d Quote Link to comment Share on other sites More sharing options...
TIGHTCHOKE Posted September 25 Report Share Posted September 25 Well done, another one saved. Quote Link to comment Share on other sites More sharing options...
Stimo22 Posted September 25 Report Share Posted September 25 On 08/07/2024 at 10:12, snarepeg said: Ha, but this is a 28 guage, love it( sometimes😊) on s/s, have just got a WW GREENER in very nice condition for £75less than a slab of cartridges and from agunshop at that, he has a rack of s/s so dont be booking an Holliday on what you will get. will perceiver with it, there is an answer to the problem, mystic meg might be next 👍😊🇬🇧 Do you mean £75 less than a slab, because I pay less than that for cartridges. If it was that cheap do they have any more Quote Link to comment Share on other sites More sharing options...
snarepeg Posted September 25 Author Report Share Posted September 25 Yes. nice Greener S/S boxlock non ejector. 30 inch barrels 1/2 -and 1/4 choke. clean bores nice overall and Prince of Wales stock. Got it for £75 and works as good as it loooks. some nice English s/s 20 bores in as well, its a buyers market on s/s👍 Quote Link to comment Share on other sites More sharing options...
BobbyH Posted September 25 Report Share Posted September 25 I do like shooting my SxS!! And well done on fixing the problem, it’s always so satisfying to diagnose and rectify a problem! Well done! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.