samboy Posted June 1, 2020 Report Share Posted June 1, 2020 Hi gang. I've just borrowed one of the above and when i pull the bolt back the magazine pops out on its own. You have to catch it. This never happened on my S410, any ideas chaps ?. Also it has an AGS scope on it which seems to have no adjustment on it to make it clearer to see through. It has a thin ring that turns on the objective lens end of the scope but it seems to do nothing when i turn it to and fro. There is nothing that moves on the eyeball end except the magnification knob. Any thoughts chaps. Thanks all. Quote Link to comment Share on other sites More sharing options...
7daysinaweek Posted June 1, 2020 Report Share Posted June 1, 2020 That does not happen on mine. That is all I can add, hope you get sorted. Quote Link to comment Share on other sites More sharing options...
strimmer_13 Posted June 1, 2020 Report Share Posted June 1, 2020 (edited) Is it a ags 3-9x40? I found close up it was useless and blurry. I think the parallax is set for 25yards. You should be able to adjust it, if not it might of been unscrewed too much and either let the gas out or let moisture in? Edited June 1, 2020 by strimmer_13 Quote Link to comment Share on other sites More sharing options...
samboy Posted June 1, 2020 Author Report Share Posted June 1, 2020 2 minutes ago, strimmer_13 said: Is it a ags 3-9x40? I found close up it was useless and blurry. I think the parallax is set for 25yards. You should be able to adjust it, if not it might of been unscrewed too much and either let the gas out or let moisture in? 3-9x50. Its clearer when i look through it with my glasses on. Quote Link to comment Share on other sites More sharing options...
bruno22rf Posted June 1, 2020 Report Share Posted June 1, 2020 If your mag is popping out your quickest test is to beg/steal/borrow another one and see if the problem persists. Quote Link to comment Share on other sites More sharing options...
samboy Posted June 1, 2020 Author Report Share Posted June 1, 2020 2 hours ago, bruno22rf said: If your mag is popping out your quickest test is to beg/steal/borrow another one and see if the problem persists. Just found another mag in the gunslip, put it in the rifle pulled the bolt and it stayed put. I will have a look at them both tomorrow to see if there's a fault on the other one . Quote Link to comment Share on other sites More sharing options...
oldypigeonpopper Posted June 1, 2020 Report Share Posted June 1, 2020 Hello, does the scope have a rear diopter that's plus or minus marks Quote Link to comment Share on other sites More sharing options...
samboy Posted June 1, 2020 Author Report Share Posted June 1, 2020 No, It only has the mag ring. But on top of the front of the scope it has printed on it 3-9x50 md2 mildot adj @ 35 yds. Quote Link to comment Share on other sites More sharing options...
oldypigeonpopper Posted June 1, 2020 Report Share Posted June 1, 2020 41 minutes ago, samboy said: No, It only has the mag ring. But on top of the front of the scope it has printed on it 3-9x50 md2 mildot adj @ 35 yds. OK I will reply later on what you can do Quote Link to comment Share on other sites More sharing options...
oldypigeonpopper Posted June 1, 2020 Report Share Posted June 1, 2020 13 minutes ago, oldypigeonpopper said: OK I will reply later on what you can do OK this is what I have done with my hawke scope, it is a older version of the vantage and fitted on a pcp air rifle, I still had to use glasses with the filter on max, so I tried what the pard 019 needs an added close up lens, this required a 37mm od lens plus 2 which I taped on the rear eye piece and it works well without the need to use glasses , so measure your scope eye piece and check out on eBay, close up lenses. You can buy 2 x / 4 x up to 10 x I bought some called rise UK from aliexpress cheaper than eBay, try a 2 x close up lens about a fiver, hope this helps Quote Link to comment Share on other sites More sharing options...
samboy Posted June 2, 2020 Author Report Share Posted June 2, 2020 9 hours ago, oldypigeonpopper said: OK this is what I have done with my hawke scope, it is a older version of the vantage and fitted on a pcp air rifle, I still had to use glasses with the filter on max, so I tried what the pard 019 needs an added close up lens, this required a 37mm od lens plus 2 which I taped on the rear eye piece and it works well without the need to use glasses , so measure your scope eye piece and check out on eBay, close up lenses. You can buy 2 x / 4 x up to 10 x I bought some called rise UK from aliexpress cheaper than eBay, try a 2 x close up lens about a fiver, hope this helps Ok thanks for info i understand what your saying so will give it a try. Quote Link to comment Share on other sites More sharing options...
dessyb Posted June 2, 2020 Report Share Posted June 2, 2020 this may sound strange but are the mags gen aa and not 3d printed.i got a spare mag for the other halfs s200 3d printed and it would not work Quote Link to comment Share on other sites More sharing options...
samboy Posted June 2, 2020 Author Report Share Posted June 2, 2020 This is my mates gun and he's had it about 10 yrs and he said the mag has never jumped out on its own before. Quote Link to comment Share on other sites More sharing options...
old man Posted June 8, 2020 Report Share Posted June 8, 2020 On 02/06/2020 at 10:09, dessyb said: this may sound strange but are the mags gen aa and not 3d printed.i got a spare mag for the other halfs s200 3d printed and it would not work One I bought for the S200 didn't work either. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.