Jump to content

Cabinet in the loft


nicknsd1978
 Share

Recommended Posts

I'm looking for people's advice in regards to fitting my cabinet in the loft. I'm moving into a new property and managed to drill a small hole to see how big cavity is behind the wall (it's a relatively new house) in total from the face of the plasterboard it's about 1 1/2 inch...the only other option I have is keeping it in the loft. The boiler is actually also in the loft...what do people think? The loft was the last place I wanted to keep it but looks like I have no option

Link to comment
Share on other sites

I'd like to go with the threaded bar idea but what do people do for behind the plasterboard? I thought of putting some washers on to act as spacers but an inch and a half of washers may be a little excessive

blue plastic water main pipe cut to the desired length will do that job, or expanding foam maybe?

Link to comment
Share on other sites

make hole around threaded bar, wind on nut till a repair washer sits flush,put cabinet on,another repair washer and a nut do it up tight with a socket.Cabinet is now trapped between washers and will pass for security.

 

Plaster board is not hollow all over. at regular intervals it will have drywall adhesive behind giving a solid spot.

Edited by Rupert
Link to comment
Share on other sites

If it is in the loft, can you not cut a larger hole around the fixing bolt and use a piece of timber as a spacer. I have plasterboard over the brick in the room where my cabinet is situated. I simply cut a 2" wide section away and let in a horizontal section of 2" x 1" baton, drilled holes through for the fixing bolts and then put the bolts right through the baton and into the brick.

Link to comment
Share on other sites

Ah! from what you describe it's not timber framed but plaster board face then thermal block then cavity then brick.

 

Drill right through, epoxy-resin some threaded bar into the wall, cut to length, and fit cabinet to these with lock-nuts.

 

Mike.

 

This sounds like the way to go, no need to go in the loft.

Link to comment
Share on other sites

Drill right through, epoxy-resin some threaded bar into the wall, cut to length, and fit cabinet to these with lock-nuts.

 

Mike.

Yes and cut a sleeve of copper pipe to slip over the studs, just the same length from the face of the plasterboard back to the blockwork. That way you can tighten onto something solid without compressing the dot and dab plasterboard.

Link to comment
Share on other sites

If the loft is the only option then ok,but I would look for somewhere less of a faf on.i know my FEO would pop the question ,would you really bang around in the loft at 3am in the morning after s night out with the NV Or would you just put the rifle/ bolt & bullets away in the morning ? I know mywife would want it in the loft for this reason alone,it makes a bad enough noise downstairs lol.

Link to comment
Share on other sites

Use resin and threaded rod. Then cut out plasterboard. Just enough to fit in some wood as a packer, It must fit tightly between plaster and block work. Fix the wood to the wall with some big screws. Then re-fix the plasterboard back over the top. And for good measure, bung in some coach bolts into the wood and into the joists if there are spare holes. Solid.

Edited by Highlandladdie
Link to comment
Share on other sites

Use resin and threaded rod. Then cut out plasterboard. Just enough to fit in some wood as a packer, It must fit tightly between plaster and block work. Fix the wood to the wall with some big screws. Then re-fix the plasterboard back over the top. And for good measure, bung in some coach bolts into the wood and into the joists if there are spare holes. Solid.

+1 deffo the best solution.

Link to comment
Share on other sites

My friend had to put his in the loft, but he also then installed a really good loft ladder system and stuff to make it really easy access. Also had to do other means to keep it warmer as it's freezing up there then boiling etc.... something to think about too

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...