Jump to content
Sign in to follow this  
JDog

Bergara seats.

Recommended Posts

A chap I know engineer with a knack for problem solving had this problem.

 

Removed the legs and got a large drill bit & slightly counter sunk the holes so that your finger performed a better push, your only talking a fraction to get it working.

 

Ditchman will understand and could possibly explain better.

Share this post


Link to post
Share on other sites

A chap I know engineer with a knack for problem solving had this problem.

 

Removed the legs and got a large drill bit & slightly counter sunk the holes so that your finger performed a better push, your only talking a fraction to get it working.

 

Ditchman will understand and could possibly explain better.

 

 

Im not even going to try :lol:

Share this post


Link to post
Share on other sites

Have to agree with Wymberley, I think maybe some of the PW members have soft hands!! 😂. Set mine up today not a problem at all but then my hands are rough and gnarly from laying bricks and blocks all day

Share this post


Link to post
Share on other sites

after reading all this, I think I will stick to my £5 plastic chutney barrel I bought from the game fair many years ago . my missis said I haven't got soft fingers any more anyway.

Share this post


Link to post
Share on other sites

after reading all this, I think I will stick to my £5 plastic chutney barrel I bought from the game fair many years ago . my missis said I haven't got soft fingers any more anyway.

 

 

 

oohhh to much information there my boy... :oops:

Share this post


Link to post
Share on other sites

I received my PW seat from Teal today, unpacked it and gave the legs and buttons a spray with silicon as it works well on plastic plus its cleaner than WD40, assembled it with no problems, I then tried to dissemble the legs, I found that if you squeezed the buttons and then lever the leg towards the centre of the seat they came out easy, pulling was more difficult, adjusting the height was also easy, just squeezed the buttons and twisted the leg, again pulling was more difficult.

 

Just a couple of niggles, the seat padding is thin, I would imagine it would give you bum ache in a very short time, the back of the seat is to upright but I can see a way to adjust this, and finally the weight, its quite heavy, just under 3 kilo which is about the same as 3 boxes of 12 gauge cartridges so unless its a short walk on the winter rape I will keep it for the stubbles.

 

Overall the seat is well made if a little expensive, time will tell how it performs in the field.

Share this post


Link to post
Share on other sites

Mine is fantastic and no problem to carry to my peg on driven days, certainly no where like two slabs of 12 gauge !!

In fact at times my wife carries it without complaint.

Share this post


Link to post
Share on other sites

think Muncher has the no-nonsense answer......drill the muther out and slap in a few tractor pins......

 

No drill required 6mm d/D pins from any agricultural store .

Share this post


Link to post
Share on other sites

I found that, as has previously been mentioned, to countersink the holes makes it easier to adjust. Then a squirt of lubricant.

Also I use the top off a bucket seat (the revolving type) which fits perfectly and is far more comfortable.

Keeping it assembled when able to drive to the hide position safes time setting up.

I have found it good for the back when out for long periods.

 

OB

Share this post


Link to post
Share on other sites

I found that, as has previously been mentioned, to countersink the holes makes it easier to adjust. Then a squirt of lubricant.

Also I use the top off a bucket seat (the revolving type) which fits perfectly and is far more comfortable.

Keeping it assembled when able to drive to the hide position safes time setting up.

I have found it good for the back when out for long periods.

 

OB

 

 

 

if you rekon that is good for the back....all i can say is "you must be on strong prescription drugs".....MMmmm yummy... :lol:

Share this post


Link to post
Share on other sites

You`re probably right Ditchy, `Good for the back` is not the right terminology. Perhaps `a little better than backless seats` would be more appropriate.

 

However, my ageing bones cannot take to sitting for long periods so maybe some strong prescription drugs are the answer.

 

Any suggestions Ditchy ?

 

OB

Share this post


Link to post
Share on other sites

well i would not waist my money on them.they have not had a good report.

 

Nothing like making your own mind up :)

 

Don't listen to the softies with fake manicured finger nails, the seats are excellent.

 

Yes a fishing chair would be more comfortable, but have you tried standing up from one with an 8lb sotgun and in a hurry?

 

I do remember Denny Essex shooting from a "comfy" type chair without standing, went over backwards into the ditch, it was rather funny :)

Share this post


Link to post
Share on other sites

You`re probably right Ditchy, `Good for the back` is not the right terminology. Perhaps `a little better than backless seats` would be more appropriate.

 

However, my ageing bones cannot take to sitting for long periods so maybe some strong prescription drugs are the answer.

 

Any suggestions Ditchy ?

 

OB

 

 

when i was young i used to stand all the time.....as i matured i used a shooting stick...then i got older and sat on a nice chair............nowww im on a bloody sun lounger.... :lol:

Share this post


Link to post
Share on other sites

No need to countersink the holes, change the pins or anything else that drastic.... A simple squirt of WD40 up the inside of the legs every once in a while and the legs pins glide in and out like silk.  Just repeat after a few trips when they start to stiffen up again. 

And Google 'bistro stool cushions' for a neat round little pad to make them more comfortable over long periods.. Two cushions in one outer cover is perfect.... And I'm 18 stone. 

Share this post


Link to post
Share on other sites

Nearly 18 months since this thread got going and still moaning about adjusting the legs. I made these 'pliers' when I first got mine. I even e mailed the Bergara Company about them and never got a reply ... very rude.  Solves the problem.  The 'noses' are slightly indented to engage the studs.  I made a leather pouch which hangs on the chair ready for use.

001.JPG

Edited by Walker570

Share this post


Link to post
Share on other sites
On 02/11/2018 at 21:07, Walker570 said:

Nearly 18 months since this thread got going and still moaning about adjusting the legs. I made these 'pliers' when I first got mine. I even e mailed the Bergara Company about them and never got a reply ... very rude.  Solves the problem.  The 'noses' are slightly indented to engage the studs.  I made a leather pouch which hangs on the chair ready for use.

001.JPG

Very neat tool! If you wanted someone to see it you could email to Ruag who have always been very good and they are the UK importer, and might be able to show it to Bergara? Appreciate you may not wish to having been blanked by Bergara previously. 

Share this post


Link to post
Share on other sites
23 hours ago, Teal said:

Very neat tool! If you wanted someone to see it you could email to Ruag who have always been very good and they are the UK importer, and might be able to show it to Bergara? Appreciate you may not wish to having been blanked by Bergara previously. 

I have been insulted by pros Teal.  AA ignored my approach re a loader for their TX200 for arthritic old codgers like me but I still think their rifles are the bees Knees.  I still think the Bergara Stag seat is very useful and a good bit of kit..... just thought they could have developed a few useful add ons ...like the enlarge feet I made for mine for soft ground and the rifle rest I made for it to slide into the holes which normally store the legs....excellent out of a pop up blind or simply zeroing.  Their loss not mine.

Share this post


Link to post
Share on other sites

I quite like mine but do agree with the problem with the leg adjustment problem. I have however now overcome that by using a tapered countersink tool and opening the hole slightly with the countersink. I can now get my podgy fingers to push it in far enough to allow adjustment. Be careful though don’t be too heavy handed with the countersink tool as you could knacker the leg. I know a few people that have now done this and are much happier with their seats.

Share this post


Link to post
Share on other sites

I have one and used to hate stripping it at the end on the day especially with cold hands.  Now I just leave it assembled and it fits perfectly in my large Jack Pyke rucksack seat to the bottom and it makes a useful frame for it.  Bought an additional cushion for it that makes it a lot comfier.

Share this post


Link to post
Share on other sites
Quote

This must be the most overpriced and uncomfortable shooting seat ever produced ,,unless you are a hobbit or smaller this will remove the most sensitive part of your tail, ,,seat very rickety no mater what setting interconnections between legs and seat base very suspect ,lean to the left it creaks and grunts lean to the to the right the same thing happens,  if you have the courage to place your posterior on  the said seat , comfort nil, stability nil , spent most of my time worrying about the security of the seat rather than concentrating on the job in hand IE shooting some pigeon.  Have tried it for nighttime duck flighting impossible to reset in the dark, all day pigeon flighting whoever designed this piece of kit it was not for shooters.. 

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...